JVFYI PCIe I350AM4 Quad-RJ45 Gigabit Server Card

Halogen-free dual- or quad-port Gigabit Ethernet adapters with copper or fiber interface options

Innovative power management features including Energy Efficient Ethernet (EEE) and DMA Coalescingfor increased efficiency and reduced power consumption

Flexible I/O virtualization for port partitioning and quality of service (QoS) of up to 32 virtual ports

Scalable iSCSI performance delivering cost-effective SAN connectivity

High-performing bridgeless design supporting PCI Express* Gen 2.1 5GT/s

Reliable and proven Gigabit Ethernet technology from Intel Corporation

Controller Intel NHI350AM4

Transmission Rate Per Port 10/100/1000 Mbps

Network Standard Physical Layer Interfaces 10BASE-T Cat3/4/5/5E/6:100m most

100BASE-Tx Cat5/5E/6:100m most

1000BASE-T Cat5E/6:100m most

Jumbo Frame Support Up to 9.5 KB

Operating Temperature 0 °C to 55 °C (32 °F to 131 °F)

Boot Option and Virtualization PXE support, Intel® VT-c

LED Indicators 1000Mbps: Yellow and Green Blinking

100Mbps: Green and Green Blinking, 10Mbps: Not illuminate

Power Supply PCI Express +12V±8% / +3.3V±9%

SYSTEM SUPPORT Windows Server 2003 / 2008 /2008 R2 / 2012 /2012 R2 /2016 R2

Windows XP / Vista / 7 / 8 / 8.1 / 10

Linux Stable Kernel version 2.4.x / 2.6.x / 3.x / 4.x or later

Linux SLES 10 / 11 or later

Package content

1 x PCIe Network card

1 x Users Manual

1 x CD Driver

1 x Low profile bracket

Accessories

System Requirements

FreeBSD, Linux , VMWare ESXi, Win7/ Win-server2012/ Win-server2008/ Win8/Win8.1/Win-server2016/win10

Available PCI Express x1/x4/x8/x16 slot

Cabling Requirements:

Intel 1 Gigabit adapters

For 1000BASE-T OR 100BASE-TX.use Category 5 or Category5e wiring, twisted 4-pair copper:

Make sure you use Category 5 cabling that complies with the TIA-568 wiring specification For more information on this specification.

Length is 100 meters max.

Category 3 wiring supports only 10Mbps

CAUTION: If using less than 4-pair cabling, you must manually configure the speed and duplex setting of the adapter and the link partner. In addition, with 2-and3-pair cabling the adapter can only achieve speeds of up to 100Mbps

For 100BASE-TX.use Category 5 wiring.

For10BASE-T.use Category 3 or 5wiring

Hardware installation

1.Turn off the computer and unplug the power cord

2.Remove the computer cover and the adapter slot cover from the slot that matches your adapter

3.Insert the adapter edge connector into the slot and secure the bracket to the chassis

4.Replace the computer cover ,then plug in the power cord

5.Power on the computer

Install Drivers and software

Windows Operating Systems

You must have administrative rights to the operating system to install the drivers.

1.insert the CD driver bound with Intel network driver into your CD-ROM drive(also you can download the latest drivers from support website):

2.if the Found New Hardware Wizard screen is displayed, click Cancel

3.start the autorun located in the software package, the autorun may automatically start after you have extracted files.

4.Click install Drivers and Software

5.Follow the instructions in the install wizard to finish it

Installing Linux Drivers from Source Code

1.Download and expand the base driver tar file.

2.Compile the driver module

3.Install the module using the modprobe command

4.Assign an IP address using the ifconfig command

Support

More information and settings, please refer to the Intel Adapter User Guides or you can contact us.